Category Archives: NEWS (ENG)

NEWS (ENG)

Recently Hot Products USA announced that there are available Gasket Kits and Individual gaskets for Sea Doo 4-Tec Engine. This gives the unique opportunity for every workshop to be equipped instantly with the required gaskets prior fixing any 4-TEC motor. Call for availability at Hot Products USA.

(Speed Control Override): The new R&D Ultra 300X Speed-up Module was developed to easily install and interface between the stock speedometer and the O.E.M. ECU to recondition and regulate the Htz rate which will allow the Kawasaki drive by wire throttle system to operate at a 1-1 ratio (No Boost Limit Control). The new R&D Speed Control module cancels out all top speed controlling throttle plate manipulation from the ECU. Without the R&D Module, the ECU can regulate the throttle plate which lowers air flow volumes, and boost levels into the intake manifold plenum restricting top speed. The R&D Speed Control Module allows full boost levels to be achieved which produce a 3-4 MPH speed gain on a box stock Ultra 300X. The R&D Module will allow all aftermarket bolt-on parts to perform to their full potential. The R&D Module interface is undetected (stealth) to the ECU, so no warnings, codes, or stored information to worry about. The R&D Module plugs into the O.E.M. wire harness super easy in 5-10 minutes. A 3-4 MPH plug and play speed gain in less than 10 minutes. No tools required to install. Above all it is made in the USA. Features: 3-4 MPH top speed improvement, Retains O.E.M dash functions, Eco mode, and Cruise Control, Plugs into O.E.M. harness terminals for a factory looking install, completely stealth to the ECU, Improved RPM performance (up to 300+), Full Boost levels achieved (2 pound boost addition), Top speed performance significantly improved, 10 minute plug and play performance, Works well with all other performance bolt on parts (R&D Ride Plate & Aquavein Scoop Grates). Pt. #801-15300 $199.95

Steve Webster is probably a true stand-up fun and he keeps working hard on them no matter how the facts are changing in the pwc market. Recently has introduced a new line up of chin pads that could fit the RRP, UMI Racing and Super Jet handlepoles. The particular chin pads are manufactured by Jettrim which is obvious if you see the mats and the high quality of stitching. Gary Hart owner of Jettrim has put his personal touch to each and every one of them. For more details, price and availability contact Steve Webster at www.kommanderind.com

Yamaha USA has recently informed Jetskiworld.gr about the new models that will be released in the near future. There is a lot of talking about Yamaha releasing a new stand-up with a four stroke engine, though the issues related to the warranty is something that worries the company a lot therefore, it has not been confirmed officially whether Yamaha will make its move this year. According to out source from Yamaha USA the new Waverunner 2012 line up will be released in the third week of August at the Yamaha Dealers’s meeting in USA.

R&D has spent lots of hours on testing impellers for the new Yamaha. While preparing for the Mark Hahn 300 2011 race tests proved the following results that are recommended for the people o racers that need something more out of the stock package. Note: R&D also has replacement impellors available for the Yamaha VXR. Pt. # 132-11319 R&D/Skat-Trak 13/19 Stainless Steel Replacement Impellor which will directly replace damaged or worn O.E.M. impellors. Pt. # 132-11218 R&D/Skat-Trak 12/18 Stainless Steel High Performance Impellors will work well in south of the equator areas where salt water is known to be heavier, as well as air quality to be heavier on humidity. Pt. # 132-11219 R&D/Skat-Trak 12/19 Stainless Steel High Performance Impellors will work well in the R&D Performer and Stage 1 Kits using R1, R2 or R3 ECU Programs. The 12/19 is the overall R&D Team favorite for all around best low end response, as well as great top speed performance (.5 MPH speed improvement over stock).

If you are an independent BRP Technician then welcome to BRP Diagnostics: “we are your specialist supplier of diagnostic equipment to suit all types of Recreational vehicles, please click on the links for more information on all our products. BRP:we can supply OEM style BUDS diagnostic systems for all BRP products such as:Seadoo , Skidoo , Can Am , E Tec & Spyder, as well as supplying Licence keys for all BRP programs & MPI/MPI-2 interfaces. We are also currently developing the DIUS programs with advanced features over any BUDS system. YAMAHA: For Yamaha owners we can supply the genuine Yamaha YDS dealer system to suit all EFI PWC/Waverunners & Outboard motors complete with interface & manuals/software on CD. AD100: we are also distributor for the AD100 multi brand diagnostic system , this system covers a wide range of PWC , Outboard & Inboard marine applications making this a perfect tool for the independent workshop. For more information log in to www.brpdiagnostics.com

The French company has designed various steering systems for most popular personal watercraft. Some of those systems incorporate a built in shock absorber that enhances rider’s comfort especially in Endurance Racing. All Idiartec steering systems are CNC machined from billet aluminum and are anodized to withstand corrosion. They are available in short and high columns or adjustable ones. Prices vary depending on the model and the special features. The particular one has been designed for the Kawasaki Ultra.